*Compatible for methanol and E85 for competitive drag race use only- when draining and flushing after each race event
* These pumps are not for use on aircraft of any type.
* Overall pump dimensions: 9.5" Long; 4.75" Wide; 2.75" Tall
These pumps do not have an internal bypass. A bypass style regulator and return line are required.
HP estimates are based on gasoline. Estimates calculated at 18.5V and at .5 BSFC NA and .65 BSFC FI. Individual systems will vary based on fuel system design, regulator type, fuel cell location, launch G's, etc.
Proper fuel system engineering is critical for maximum performance.
This pump is not designed to use a standard conical seat style union in the inlet or outlet of the pump. Example: Part # AT981510ERL. Use of this style fitting will block flow and WILL lead to poor performance and pump failure. The ONLY correct fitting to use is a contoured port fitting with an O-ring seal such as :Part # AT985010ERL.
Holley set the bar in 2011 with the release of the HP and Dominator in-line fuel pumps. In 2015, Holley has raised the bar again with the introduction of the VR1 and VR2 Brushless in-line fuel pumps. Featuring brushless pump technology and a twin screw rotor design, the VR1 and VR2 in-line fuel pumps are capable of high pressures and flows while maintaining a low amperage draw and quiet performance. Designed to work on high boosted race cars as well as your daily driven weekend endurance car, these pumps work with gasoline, methanol, and E-85* (Compatible for methanol and E85 for competitive drag race use only- when draining and flushing after each race event) and can maintain pressures of 130 PSI and up to 335 GPH flow**. Fueled by TI Automotive.
The pumps include a 2 step controller for pump speed control.
The pumps can be ran in one of two different speeds. A low speed
control for low fuel consumption requirements or at full speed
for high fuel consumption requirements. The VR2 includes (2) controllers for precise control of both pumps independently of each other. Both the VR1 and VR2 pumps are proven for 18.5V compatibility.
**At 13.8V
* Overall pump dimensions: 9.5" Long; 4.75" Wide; 2.75" Tall
Features:
Capable of 130 PSI while providing significant flow for forced induction applications where belt driven pumps are normally used.
Unlike other pumps, the VR Series are built for continuous duty if needed.
The dual pump models are designed for endurance racing where both pumps are used or one can be a reserve pump.
Billet aluminum construction for durability and good looks
Features a single 16 AN O-ring inlet and a single 10 AN O-ring outlet
High flow and high pressure with low amperage draw
Can be fully submerged in the fuel cell or chassis mounted
Maximum amp draw of 38 AMPS for the VR2
Holley also offers a complete line of fuel filters and fuel pressure regulators that are designed to work as a system with these pumps
This part is legal for use on Uncontrolled (Non-Emissions Controlled) Vehicles or Racing Vehicles.
The following vehicles are considered Uncontrolled (Non-Emissions Controlled) Vehicles:
1965 and older U.S. manufactured California Certified vehicles
1967 and older U.S. manufactured Federally Certified vehicles
1967 and older Foreign manufactured vehicle
Racing Vehicles are vehicles that are used exclusively for racing or other forms of competition that are not registered and that may never be used on the street.
*Compatible for methanol and E85 for competitive drag race use only- when draining and flushing after each race event
* These pumps are not for use on aircraft of any type.
* Overall pump dimensions: 9.5" Long; 4.75" Wide; 2.75" Tall
These pumps do not have an internal bypass. A bypass style regulator and return line are required.
HP estimates are based on gasoline. Estimates calculated at 18.5V and at .5 BSFC NA and .65 BSFC FI. Individual systems will vary based on fuel system design, regulator type, fuel cell location, launch G's, etc.
Proper fuel system engineering is critical for maximum performance.
This pump is not designed to use a standard conical seat style union in the inlet or outlet of the pump. Example: Part # AT981510ERL. Use of this style fitting will block flow and WILL lead to poor performance and pump failure. The ONLY correct fitting to use is a contoured port fitting with an O-ring seal such as :Part # AT985010ERL.
*Free Shipping & Handling only offered to the contiguous US on orders over $100.
Some parts are not legal for use in California or other states with similar regulations.