Skip to main content

SEMA Stories: Darren King Talks About His Dutchboys-built ’69 Torino

11/16/2026

SEMA Stories: Darren King Talks About His Dutchboys-built ’69 Torino

11/16/2026

Having wowed the SEMA Show crowds in 2025 with Dennis King’s award winning, 1969 Ford Torino, the team at Dutchboys Hotrods did it again at SEMA in 2026 by revealing another stunning ’69 Torino build – this time owned by Dennis’s brother, Darren.


“My brother has had his car since he was a kid,” explains Darren. “When my dad [Jim] retired, we start talking to Paul and Joe VanNus [at Dutchboys], and my dad said, ‘You know what? If we’re going to do one, we might as well do two. I’ve got two kids with different mindsets on what a car should look like.’ At that point, we just started building.”


Sadly, Jim passed away in April 2025, so did not live to see the project’s completion. He is remembered in a custom-made badge on the rear of Darren’s purple Torino, has his signature in a badge on the dash, and even gets to ride along, as some of his ashes are carried in the center console.


Like Dennis’s machine, Darren’s Torino rides on a Roadster Shop Fast Track chassis that was custom-built for the project and sits up inside the rocker panels. Dutchboys cut the whole car, from the cowl panel to the tail, and made flat floors: “There’s no exhaust hanging down,” says Paul VanNus. “Everything is tucked up inside that chassis.



“There are some similarities, but this car is quite a bit different to the last one,” he continues. “We fabricated a different, custom hood and extended the rockers forward. The hood scoop is usually fiberglass but the custom hood leans closer to the factory look and incorporates a custom hood scoop designed to fit into our custom cowl. We also altered the lower quarter panels.”


At the front of the car, little remains of the stock bumper, which has been tucked in. The marker lights were eliminated, and the turn signals have been relocated to the headlights, with the ‘482’ badges in the side of the air cleaner acting as repeaters.


Darren King – a millwright whose father started a machine shop in 1975 and encouraged Paul and Joe to expand their own machining capabilities – machined a new, one-piece grille from a 600-lb billet.


“I made the first version probably six years ago,” he says. “And then I revamped it three years ago because we needed to recess it a little further.”


Below the bumper is a handmade, aluminum splitter. Observes VanNus, “A lot of stuff has been altered in the front of this car but has been made to look like it has not been changed at all. That’s what we like to do: make a lot of alterations, but make it look like it should or could have been that way from the factory.”

The rear end is a substantial departure from stock, too, with substantially wider, Shelby-style taillights. Exhaust cutouts are incorporated and all the trim is newly made, as at the front. But in other areas, the body retains its factory details – the Torino still has its drip rails, for example.


“We kept all the window trim, but it’s been fitted and chrome plated,” VanNus continues. “We want to keep a very classic, timeless look for this car so that 10 years from now, it will still look good.”


In the same vein, the chunky, chrome windshield surround has been kept, but refined, and the factory mirrors are recessed into the door pockets. Advanced Plating handled all the chrome plating.


“The fitment of all this stuff was blocked and gapped, and then sent off to get chromed,” he says. “There is a lot of refinement in all this factory trim to make it look and fit like it does.”


Like his brother’s Torino, Darren’s car has an all-aluminum, 482, big-block FE motor. A Holley Terminator X setup provides fuel injection while retaining the classic, dual-four-barrel, carbureted look. There’s also an MSD distributor. The FE is paired with a Bowler/Tremec T-56 transmission.



The fully custom interior was awarded the 2026 TRIM Champion Best of Show Award at SEMA. Dutchboys used a variety of textures, including Moore & Giles leather, and wrapped it up with in-house-machined, stainless-steel interior eye candy. The dash, center console, package tray and door panels were all CAD-modeled and 3D-printed in-house, and the interior was designed and engineered with hidden fasteners. There is also a roll cage made from 1⅝-inch Chromoly tubing.


“There have been some changes along the way with these cars,” says VanNus, “just things that we can do as a shop now, but weren’t capable of doing back when we started the Torinos – like the CNC machining or the 3D printing. This is a better car today because of those things that we can implement in it. There were some backward steps along the way, to refine it, but luckily the customer was good with us, and we continued to raise the level of the car.”



One thing Darren King insisted upon from the start was the ‘Deep Purple Haze’ paint, which is a major contributor to giving the Ford a more elegant vibe than Dennis’s more Pro Touring-looking machine. At SEMA, it was a finalist for the Chip Foose Best Paint Award by Surventis. Says the builder, “We did a custom mix, took a BASF color and darkened it up. It flops around outside in the sun and under different lights. We added a custom stripe on the hood in matte black.”


Check out our SEMA coverage here and see the new products we introduced at the show.


The finishing touch is provided by a set of Forgeline ‘Grudge’ wheels (19x10 front, 20x12 rear) that were blasted and coated for a cast-like finish. Dutchboys machined custom center caps, too. Behind the Michelin Pilot Sport 4S-shod rims are Baer brakes: six-piston calipers with a nickel finish, and 14-inch rotors.


The purple Torino has been a long time in the making, but Darren now intends to make the most of it. “I’ll go to shows and drive it,” he says. “We consider our cars to be drivers. We believe that if you don’t drive them, why have them? So, we’re going to get in them, and go.”

author

55 Posts