Skip to main content
Motor Life Events Community Support
4
Images
Videos
Holley Sniper EFI

HyperSpark Kit w/ 565-305 - Chrysler 383 / 400

Part # 565-305K Be the first to write a review

Includes distributor, ignition box, ignition coil, and main harness

HyperSpark Kit w/ 565-305 - Chrysler 383 / 400

In Stock
Free Shipping - Lower 48 US States
$999.95
Add to Wishlist

3

Emissions

This part is legal for sale and use on Uncontrolled (Non-Emissions Controlled) Vehicles.

See Emissions Details

Also Bought

Our HyperSpark kits were designed to make upgrading your ignition on a Sniper 1 EFI equipped engine simple. When installed along with a Sniper 1 EFI system, the combination creates the easiest conversion to install on the market, with only four connections required. Our harness only requires one connection to a switched 12V, battery+, battery-, and fuel pump power. The pre-terminated connectors and a built-in 40A relay provide power to all of the components within the system. With the main harness included, you no longer need to run multiple wires to provide switchedย 12Vย for each individual component. Route the harness and pre-terminated connectors to your HyperSpark coil, distributor, and ignition box and plug them in.

Features:

  • Plug and play main harness replaces the standard Sniper 1 EFI harness with battery+, battery-, switched 12V, and fuel pump power for a clean installation
  • HyperSpark ignition coil delivers 135mJ of spark energy during engine combustion
  • Single Hall Effect sensor provides noise-free RPM signal interference and precise timing control
  • ECU timing control or non-timing control options (Additional harnesses may be needed, refer to installation manual)
  • CNC billet aluminum distributor housing provides strength and protection
  • CNC billet machined distributor shutter wheel delivering accurate cylinder timing and accuracy at high speeds
  • Distributor shutter wheel is pinned and welded to the shaft for reliable accuracy
  • Cast distributor gear construction
  • Patented clear installation cap eliminating confusion and error during distributor install
  • Integrated ignition coil bracket simplifies mounting the Ignition coil
  • External LED on HyperSpark ignition box helps verify 12V, cranking RPM, and low battery voltage
  • Wire retainer for securing spark plug wires
  • Lucas Racing Performance Gear Break-In Lubricant for protection
  • Includes distributor, ignition box (565-151), ignition coil (565-152), and harness (558-328)
Adjustable CollarNo
Advance TypeLocked-Out
Brand Holley Sniper EFI
Cap ColorBlack
Cap Terminal GenderMale
CategoryFuel Injection - EFI
Ignition
Clamp Hardware IncludedNo
Coil Wire IncludedNo
ColorPolished
Computer Controlled CompatibleYes
Connector TypeSealed
Distributor Cap IncludedYes
Distributor Gear IncludedYes
Distributor IncludedYes
Distributor TypeHall Effect
Emission Code3
GearCast
Gear MaterialCast Iron
Grade TypePerformance
Housing ColorPolished
Housing FinishPolished
Housing MaterialBillet Aluminum
Ignition Box RequiredYes
Ignition Coil IncludedYes
Ignition Module IncludedYes
Ignition Rotor IncludedYes
Marine ApprovedNo
MaterialBillet Aluminum
Mechanical Tach Drive ProvisionNo
Part TypeDistributor
Product TypeDistributor
Rotor RotationCounterclockwise (Left)
Sub CategoryDistributor and Magneto
Trigger TypeHall Effect
WarrantyManufacturer's Limited 1 Year Warranty
UPC090127135167
Part Number565-305K
3

This part is legal for sale and use on Uncontrolled (Non-Emissions Controlled) Vehicles.


The following vehicles are considered Uncontrolled (Non-Emissions Controlled) Vehicles:

  • 1965 and older U.S. manufactured California Certified vehicles
  • 1967 and older U.S. manufactured Federally Certified vehicles
  • 1967 and older Foreign manufactured vehicle


WARNING: It is against the law to install this part on an Emissions Controlled Vehicle


The following vehicles are considered Emissions Controlled Vehicles:

  • 1966 and newer U.S. manufactured California Certified vehicles
  • 1968 and newer U.S. manufactured Federally Certified vehicles
  • 1968 and newer Foreign manufactured vehicle
Instructions - 199R11525.pdf
This is a cast distributor gear, it is recommended to consult your camshaft manufacturer prior to installation to confirm what distributor gear material they require. When changing distributor gears, it is critical to measure the shaft diameter OD and gear ID, before installing the new gear on the shaft. Designed for Sniper 1 only, new installations will not use the Sniper 1 harness or coil driver as the new main harness retains the same lead color wires.
Manufacturer's Limited 1 Year Warranty: See Details

We Suggest

Reviews

    Your Review

    *Free Shipping and Handling only offered to the contiguous US on orders over $149, excludes clearance parts and oversized packages.

    Some parts are not legal for use in California or other states with similar regulations.